Installation

To install the rails, extension table, and fence you will need the following tools:

5 mm hex driver and 6 mm hex key (included)

13 mm and 17 mm wrenches (or adjustable wrench)

Phillips head screwdriver

1. Installing the Front Rail: The rst step in installing the fence is to attach the long angle iron rails to the table.

Please see pages 10 and 12 for exploded views of the rails and extension tables. The rails are shipped in

the long cardboard box packaged with the main tube. The front rail is the larger of the two and includes 5

countersunk holes that are used to mount the rail to the front of the table. To mount the front rail, position the

rail along the front of the table with the cut-outs at the top of the rail centered on the miter gauge slots in the

table. Thread three M8 x 25 countersunk socket head bolts into the tapped holes in the front of the main table.

See Fig. 1. Tighten the bolts using the 5 mm hex driver.

Next, mount the front rail to the cast iron extension wings using two M8 x 35 countersunk socket head bolts,

two M8 washers, two M8 lock washers and two M8 hex nuts. Position the bolts through the front rail and the

extension table, then install the washer, lock washer and nut (in that order) on the end of the bolt. The holes in

the extension wings are not tapped and are slightly larger than the bolts they receive to allow you to use the

rail to pull the wings up or down slightly, if necessary, to get the wings parallel to the table. To do this you can

push down or pull up on the wing slightly and then tighten the nut to hold it in place.

page 1

Fig. 1

Use longer bolts

for mounting rail to

extension wings.

1 2 3 4 5 6 7 8 ... 17 18

Comments to this Manuals

No comments

Kramer Electronics Musical Instrument Revision 6 manuales

Manuales del propietario y guías del usuario para Accesorios de proyector Kramer Electronics Musical Instrument Revision 6.
Ofrecemos 1 manuales en pdf Kramer Electronics Musical Instrument Revision 6 para descargar gratis por tipos de documentos: Manual de usuario

Kramer electronics Musical Instrument Revision 6 Manual de usuario (94 paginas)

Marca: Kramer-electronics | Categoria: Projector accessories | Tamaño: 3.81 MB |

Inglés

Tabla de contenidos

Kramer Electronics, Ltd

1

Kramer K-Config Guide

1

Revision 6

1

Contents

2

Trademarks:

7

1.3 Trigger Types Available

10

describes

10

K-Config triggers in detail

10

Introduction

11

1.6 Quick Start

12

Table 5: Glossary

13

1.9.2 Operating Systems

14

15

4. Click Import Drivers

17

Defining the Control Room

18

Virtual Device Virtual Device

21

Auxiliary Device

21

Tab Area Settings

26

Figure 25: The Port Manager

26

Table 6: Connect Dialog Box

31

5.3 The Web Settings Tab

34

The Triggers

35

Figure 50: The Action List

37

6.7.1 Power ON Example

43

Figure 66: Set the Timeout

44

Figure 77: Set the Timeout

48

6.8.1 Digital Input

51

Setting the Digital Input

51

6.8.2 Digital Output

53

Setting the Digital Output

53

6.8.3 Analog Input

53

6.9.1 Button Behavior

55

Set K-NET IDs

66

Figure 129: Setting K-NET ID

66

9 The Driver Manager

67

The Driver Manager

68

Write the serial command

69

(see Figure 133)

69

9.1.2 Creating an IR Command

70

USB driver (see Section 2.2

70

Figure 158: Queries Area

80

Figure 160: Queries Area

82

10.1.2 Saving a Project

89

The Kramer K-Config Menus

90

10.2.1 Load Firmware

91

Figure 178: Connect Window

92

Connecting via the ETHERNET

94

Más productos y manuales para Accesorios de proyector Kramer Electronics

Modelos	Tipo de documento
Ninguno